sink mark 缩痕
LRR launch readiness review
Front bumper 前保险杠
Rear bumper 后保险杠
Radiator grille 格栅
Headlamp 前大灯
Tail lamp-liftgate 尾灯-行李箱盖上
Tail lamp-quarter 尾灯-后侧围上
Front door trim panel 前门内饰板
Rear door trim panel 后门内饰板
Interior release handle bezel 内开手把手框
Power controls bezel 电动车窗开关框
Window interior capping 窗框饰条
Exterior mirror 外后视镜
Body side moulding 防擦条
Cowl grille 通风格栅
Roof molding 车顶装饰条
Lift gate molding 牌照板支架
Lift gate handle 行李箱盖拉手
Weather strip_door openings 门框胶条
Weather strip_liftgate 行李箱胶条
A Pillar Trim A柱
B Pillar Trim upper B柱上
B Pillar Trim lower B柱下
Front scuff Plate 前门槛条
Rear scuff plate 后门槛条
Back panel trim lower 行李箱门槛条
Garnish trim-Quarter window
Cowl trim panel A柱下
Liftgate upper trim 尾门内饰板上
Liftgate side trim 尾门内饰板中
Liftgate lower trim 尾门内饰板下
IP
Defroster panel 除霜盖板
Console 中控台
Steering column cover 方向机柱上下盖板
Cluster 组合仪表
Carpet 前地毯
Trunk carpet 后地毯
Front seat 前座椅
2nd row seat 第二排座椅
burr(金属) flash(塑件)毛边
gap 间隙
defective products 不良品
finished products 成品
disposed products 处理品
band-aid 创可贴
scratch 刮伤
dents 压痕
缩水 Shrinkage
缩水 Sink Mark
顶白 Stress Mark
YC (Potential Critical Characteristic) 潜在关键特性
YS (Potential Significant Characteristic) 潜在重要特性
Restriction of Hazardous Substances 简称RoHS SGS, BV, TUV, Intertek, ETC BV-Bureau Veritas 法国国际检验局
首检 First article inspection
自检 Self-inspection
全检 100% inspection
巡检 process audit
开箱检验 out of box audit
出货检验 out-going inspection
进货检验 in-coming inspection
例行检验 Routine checking
确认检验 Confirming
全尺寸检验 full dimension inspection
可靠性试验 Reliability test
在线检验 on-line inspection
线下检验 off-line inspection
1号厂房工艺布置方案图 proposal of the Plant I layout
2 套 two kits
J型转弯试验 test of J turn
保险杠 bumper
变光开关 simmer switch
薄壳式结构 shell construction
操舵力试验 steering effort test
长途客车 inter-city bus
车辆转移台 bus transfer
衬垫 pad
除湿器 moisture ejector
搭接 lap
怠速时 at idle
底盘平移台 chassis shuttle
吊运装置 overhead hoist
镀锌板 galvanized plate
发车前准备 pre-delivery
发动机托架 engine holding frame
发动机中置式客车 bus with under floor engine
反冲试验 kick-back test
返工 re-doing
防滑地板 no-skid floor
防破坏 vandal resistant
风洞试验 wind tunnel test
改装厂 refitting factory
钢化玻璃 toughened grass
搁梁 shelf beam
更衣室 restroom
工位 station
功率突然变化影响试验 test of effect of sudden power change
合笼 mate
恒温控制 thermostatic control
横风稳定性试验 test of crosswind stability
后围侧板 rear wall side cover
互换性 interchangeability
极限侧向加速度试验 limiting lateral acceleration test
阶路响应时间试验 step response test
结构完整性 structure integrity
静态操舵力试验 static steering effort test
举升 hoist
聚碳化透镜 poly-carbonate len
空气导流板 air deflector
宽敞悬臂式座椅 roomy cantilevered seat
亮丽的外表 smart apperance
磷化 phosphating
轮胎爆破响应时间试验 test of burst response of tyre
轮辋错动试验 rim slip test
轮椅升降机 Wheel chair lift
轮罩护板 wheel house
马力小时，马力时horsepower-hour
脉冲响应试验 pulse response test
内饰 trim
耐翻倾试验 test of overturning immunity
扭矩torque
爬坡能力 grade ability
排水阀 drain valve
配电站 power transformer substation
拼装台 collector
频率响应时间试验 frequency response test
平衡水箱 surge tank
汽车平顺性单脉冲输入行驶试验 automobile ride single pulse input running test
汽车平顺性随机输入行驶试验 automobile ride random input running test
汽车悬挂系统固有频率与阻尼比的测定试验 measurement of natural frequency and damping raito of suspension
前围角板 front wall angle cover
嵌条 insertion strip
强制通风 ram-air ventilation
切割轮口 wheel -arch cutting
切齐 trimming
琴式驱动桥 banjo type drive axle
全天候空调系统 full range A/C
裙板 skirt
绕过障碍物试验 obstacle avoidance test
三类底盘 three type chassis
来源：汽车制造网
